Почините Свои Вещи Сообщество Магазин

Шестое поколение iPhone компании Apple, представленное 12 сентября 2012 года. Ремонт данного устройства схож с предыдущими моделями, требующий отвертки и инструменты для вскрытия. Доступен в версиях GSM или CDMA; с 16, 32 или 64 ГБ памяти; в Черном или Белом цвете.

2522вопросов Показать все

Опции

Missing resistor for home button iPhone 5

Hi,

I had to check the motherboard of my Iphone 5 after home button problemes

The BGA U3 resistor is there but i noticed one resistor close a connector(i don't know how it called ) is missing.

As you can see on the pic , one in the middle of the 3 resistors vanished.

Where can i get a free schematics for an iPhone 5, so i can get the correct resistor value ?

Which are the other possible ways to get the probleme fixed ?

Home button actually works with some pencil's graphite but Iphone can't be shaked and has obviously to be steady.

Can a soldering dot fix it temporary ? Where to buy this component ?

Sorry for my poor english and thanks in advance for help.

Block Image

Block Image

Отвечено! Посмотреть ответ У меня та же проблема

Это хороший вопрос?

Да Нет
Оценка 0
Добавить комментарий

3 Ответов

Фильтр:
Самые полезные Самые новые Самые старые
Выбранное решение

Опции

The missing component is a ferrite bead (FL5). It's specs are 120Ohms / 210mA / 01005. You can find them at Digikey.com under the following part number (445-8668-1-ND). It's the same component as the backlight filter.

Был ли этот ответ полезен?

Да Нет
Оценка 3

3 Комментариев:

Thank you , amazed with this fast professional reply. Unfortunately i have to find another solution because cost shipping are too high for France. Thanks again for this reference , it was so difficult to find .

из

If a micro jumper is okay , is it possible to solder any resistor since the size is same as the missing one and no matter the value ? Thanks advance for answer

Thanks in advance .

из

No, you shouldn't put a resistor in place of a ferrite bead. They have different functions. A micro-jumper is okay for testing purposes.

из

Добавить комментарий

Опции

yes this is possible to repair, you can either get a resistor from a donor board, and solder it on using a hot air work station or fine soldering tweezers, alternatively as it is a resistor you can just use a small jumper wire method. We repair these all the time, it is easy if you are experienced in micro soldering. Hope this helps.

Был ли этот ответ полезен?

Да Нет
Оценка 1

2 Комментариев:

Thank you very much.

Can i ask what is a "small jumper wire method" ?

I am not a big experienced in soldering but in think i can make a "dot", a "jumper wire" sounds different .

I was thinking that if a dot of graphite can make miracle, a solder dot can too. Thanks

из

i dont think a solder dot will be a good idea, you want to make a micro jumper between the two points, if you are unable to perform such a task, i dont mind doing it for you, i specialise in micro soldering

из

Добавить комментарий

Опции

If a micro jumper is okay , is it possible to solder any resistor since the size is same as the missing one and no matter the value ? ( here a 01005 resistor)

Thanks in advance .

Был ли этот ответ полезен?

Да Нет
Оценка 0
Добавить комментарий

Добавьте свой ответ

Marfr будет вечно благодарен.
Просмотр статистики:

За последние 24часов: 0

За последние 7 дней: 0

За последние 30 дней: 0

За всё время: 248