Эта версия возможно содержит некорректные исправления. Переключить на последнюю проверенную версию.
Выберете то, что вам нужно
-
Этот шаг не переведен. Помогите перевести
-
Before you begin, switch off your phone.
-
Apply a heated iOpener to the back of the phone to loosen the adhesive beneath the rear glass. Apply the iOpener for at least two minutes.
-
-
Этот шаг не переведен. Помогите перевести
-
Secure a suction handle to the lower edge of the rear glass, as close to the edge as possible.
-
Lift the rear glass with the suction cup to create a small gap between the glass and the frame.
-
Insert an opening pick into the gap.
-
Slide the opening pick to the bottom right corner.
-
-
Этот шаг не переведен. Помогите перевести
-
Insert a second opening pick and slide it to the bottom left corner to cut the adhesive.
-
Leave the opening picks in place to prevent the adhesive from resealing.
-
-
Этот шаг не переведен. Помогите перевести
-
Insert a third opening pick at the bottom left corner.
-
Start to slide the tip of the opening pick from the bottom left corner along the side to cut the adhesive.
-
Leave the opening pick in its place at the top left corner to prevent the adhesive from resealing.
-
-
Этот шаг не переведен. Помогите перевести
-
Insert a fourth opening pick under the top left corner of the rear glass.
-
Slide the opening pick along the top edge of the phone to cut the adhesive.
-
Leave the opening pick in the top right corner to prevent the adhesive from resealing.
-
-
Этот шаг не переведен. Помогите перевести
-
Insert a fifth opening pick at the top right corner of the phone.
-
Slide the opening pick along the right side to cut the remaining adhesive.
-
-
Этот шаг не переведен. Помогите перевести
-
Carefully lift the rear glass and fold it to the left side of the Honor 8.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the Phillips #00 screw (2.8 mm length) that secures the metal bracket on top of the fingerprint flex connector.
-
-
Этот шаг не переведен. Помогите перевести
-
Use a pair of tweezers to remove the metal bracket that sits on top of the fingerprint and display flex connectors.
-
-
Этот шаг не переведен. Помогите перевести
-
Use a spudger to pry up and disconnect the fingerprint flex connector.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove these Phillips #00 screws securing the midframe bezel:
-
Eight screws with 3.5 mm length
-
Eight screws with 2.9 mm length
-
Some screws might be covered with a tamper proof sticker.
-
-
-
Этот шаг не переведен. Помогите перевести
-
Insert an opening pick underneath the top right edge of the midframe bezel.
-
Use the opening pick to pry up the midframe bezel.
-
Insert the opening pick underneath the bottom left corner of the bezel and pry it up.
-
-
Этот шаг не переведен. Помогите перевести
-
Insert the long edge of an opening pick in the seam between the midframe and the bezel on the left side of the phone.
-
Slide the opening pick along the left side of the phone to cut the adhesive underneath the midframe bezel.
-
-
Этот шаг не переведен. Помогите перевести
-
Repeat the procedure on the right edge of the phone to cut the adhesive underneath the midframe bezel.
-
-
Этот шаг не переведен. Помогите перевести
-
Carefully grasp the midframe bezel from the bottom corners and lift it upwards.
-
Remove the midframe bezel.
-
-
Этот шаг не переведен. Помогите перевести
-
Use a spudger to pry up and disconnect the battery flex cable.
-
-
Этот шаг не переведен. Помогите перевести
-
Use a pair of tweezers to lift the black adhesive pull tab off of the top right corner of the battery.
-
Use a pair of tweezers to pull out the adhesive strip.
-
-
Этот шаг не переведен. Помогите перевести
-
Apply a heated iOpener to the screen for at least two minutes to loosen the adhesive beneath the battery.
-
Display flex cable
-
Interconnect flex cable
-
-
Этот шаг не переведен. Помогите перевести
Инструмент, используемый на этом этапе:Plastic Cards$2.99-
Insert an opening pick or a plastic card under the battery where the adhesive strip was located.
-
Slide along the right side of the battery to cut the remaining adhesive.
-
Carefully pry up the right side of the battery to loosen the adhesive.
-
-
Этот шаг не переведен. Помогите перевести
-
Slide a plastic card underneath the battery and cut the remaining adhesive between the flex cables and underneath the left side of the battery.
-
-
Этот шаг не переведен. Помогите перевести
-
Use a spudger to pry up and disconnect the display flex cable from its motherboard socket.
-
-
Этот шаг не переведен. Помогите перевести
-
Use a pair of tweezers to carefully peel the display flex cable off of the midframe.
-
-
Этот шаг не переведен. Помогите перевести
-
Use a spudger to pry up and disconnect the loudspeaker flex cable.
-
-
Этот шаг не переведен. Помогите перевести
-
Insert the flat end of a spudger under the right edge of the loudspeaker and pry to lift the loudspeaker out of its recess.
-
Remove the loudspeaker.
-
-
Этот шаг не переведен. Помогите перевести
-
Use a pair of tweezers to peel the grounding cable off of the midframe.
-
-
Этот шаг не переведен. Помогите перевести
-
Apply a heated iOpener to the display for two minutes to loosen the adhesive beneath.
-
-
Этот шаг не переведен. Помогите перевести
-
Once the screen is warm to the touch, apply a suction cup near the top edge of the phone right under the earpiece speaker.
-
Pull up the suction cup to create a gap between the screen and the display bezel.
-
Insert the tip of an opening pick in the gap you created and slide it to top right corner of the phone. Leave it there to prevent the adhesive from resealing.
-
-
Этот шаг не переведен. Помогите перевести
-
Insert a second opening pick in the gap you created and slide it to the top left corner. Leave it in its place to prevent the adhesive from resealing.
-
-
Этот шаг не переведен. Помогите перевести
-
Insert the tip of a third opening pick at the top right corner and slide it along the right edge to cut the adhesive. Leave it in the bottom right corner to prevent the adhesive from resealing.
-
-
Этот шаг не переведен. Помогите перевести
-
Insert a fourth opening pick at the bottom edge of the phone and slide it to the bottom left corner. Leave it there to prevent the adhesive from resealing.
-
-
Этот шаг не переведен. Помогите перевести
-
Insert a fifth opening pick at the bottom left corner and slide it along the left edge of the phone to cut the remaining adhesive.
-
-
Этот шаг не переведен. Помогите перевести
-
Slowly separate the screen from the frame. Make sure the flex cables are no longer stuck to the frame and carefully thread them through their gaps.
-
Remove the screen.
-
Отменить: Я не выполнил это руководство.
10 участников успешно повторили данное руководство.
6 Комментариев
WARNING !!!
Stop following the tutorial from step 27! There is a front midframe bezel similar to the one on the back, this tutorial removes the screen with the bezel still attached to it.
The fact is that Honor 8 screens are not sold with the bezel ! So don’t remove the bezel and just go for the sreen the same way you removed the back glass. This also makes the process easier since there will not be any bumps blocking the way. (step 28)
Dear Mike Le,
this is completely correct and we adjusted the guide to only remove the screen without the screen bezel and to go with the replacement part. Thank you!
Ive had an honor 8s in for repair, there seem to be two different models. every screen ive ordered has the wrong lcd connector on it.
Ive had an honor 8s in for repair, there seem to be two different models. every screen ive ordered has the wrong lcd connector on it. there seems to be a KSE-LX9 and KSA-LX9