Введение

This is my teardown of the Game boy colour.

This teardown is not a repair guide. To repair your Game Boy Color, use our service manual.

Take the Game boy and notice the way that it has been injection moulded using two tools on the injection moulder. The first thing to do is to separate these parts.
  • Take the Game boy and notice the way that it has been injection moulded using two tools on the injection moulder. The first thing to do is to separate these parts.

Добавить комментарий

Remove the Game Boys battery case from the back of the game boy and take out any batteries that are inserted. this will leave you with the back panel.
  • Remove the Game Boys battery case from the back of the game boy and take out any batteries that are inserted. this will leave you with the back panel.

Добавить комментарий

  • The Two screws at the top of the back panel can be unscrewed using a very small screw driver. the head must be very small as these are hard to get too.

Добавить комментарий

  • The other small screws in the back panel are very hard to get to you need to drill these out but be careful not to damage the gameboy because this can crack the back panel.

I don't really get why you will drill out the screws! They are special screws, and ofcourse there's also a screwdriver for them, called Tri-wing - used in many parts, including Nintendo and Apple. Look it up at Wikipedia: http://en.wikipedia.org/wiki/Tri-Wing

I've bought one myself on eBay - that's better than screwing your Game Boy up ;)

Anders Kielsholm - Ответить

Buuuh!!! Why are you using an electrical screwdriver!

That's cheating man!

Victor Szulc - Ответить

Do not use a drill or phillips head screwdriver, use a tri-wing screwdriver. This step should be edited to reflect the proper procedure.

theneovega - Ответить

  • The two panels are snap fitted so you will need to pop them part use something to wedge the crack open.

Добавить комментарий

  • To remove the main board just remove the 4 screws in the back doing this will mean you can take the board out of the abs plastic sections.

Добавить комментарий

  • The metal cassette holder on the back plastic panel can be removed by simply using a small screw driver in all four corners this should mean it pops off.

Добавить комментарий

  • The small plastic switch should just fall out of the plastic case make sure not to lose this when opening up the game boy.

Добавить комментарий

  • You can simply pull the foam off the back of the screen pulling off the glue try not to tear the foam this makes things easier later.

Добавить комментарий

  • Once the foam is off you can pull the main connection of the screen out this is the brown part of plastic sheeting it simply slides out.

Добавить комментарий

  • The rubber buttons can easily be pulled off they are not held in but will need a little pull.

Добавить комментарий

  • All the other buttons should just fall out. Be careful not to drop or lose these parts because they will come loose.

Добавить комментарий

  • Pull the screen out of the game boy and take the front panel of plastic away and move it to the side.

Добавить комментарий

  • Peel of the protective film on the LCD screen and remove the LCD screen from the casing.

Добавить комментарий

  • The metal on the screen can be pulled off by getting under it with your fingers this is stuck with a tape.

Добавить комментарий

  • some parts of the circuit board can also be removed and looked at much closer such as the speakers and the LED lights on the product.

I wish I could take a picture of my situation I've succeeded in pulling out the back cover because I need to clean my corroded battery points. I see only 2 heads on the board what do I do?

kelechi oputa - Ответить

Marcus Broughton

Участник с: 09.03.2010

347 Репутация

1 Guide authored

Комментариев: 4

That feel when everything turns out perfectly. ^.^ Thanks a lot for the guide! I was able to switch out a few broken/worn out bits, and now it's working like new! Super hyped! Thank you so much!

(Also, the screws that are mentioned needing a drill are regular phillips screws and, are indeed incredibly tough to get out without a drill. Though, the ones in my Gameboy were somehow already stripped pretty badly.)

Dayna - Ответить

DEFINITELY do NOT need to use a drill to open a Gameboy Color!

Thomas Nunya - Ответить

The 6 screws to open the case ARE NOT PHILLIPS! They are Tri-Wing, a Y shaped driver, not + shaped. If you use a phillips head screwdriver, you will strip them quickly, and then you actually will have to drill them out. Use the right tool every time!

theneovega - Ответить

I had to open it up once because I forgot to connect the ribbon, but thanks for the guide! It was quite helpful.

Dillon Henry - Ответить

Добавить комментарий

Просмотр статистики:

За 24 часа: 8

За 7 дней: 57

За 30 дней: 293

За всё время: 26,056