Вики, созданная, благодаря помощи студентов
Эта вики выполнена отличной студенческой командой из нашей образовательной программы.
Battery Won’t Charge
Your battery is not charging while in the charger, and does not hold charge for long once in use.
Faulty Connection
When placing your battery to charge, make sure that the battery snaps into the charger similarly to how it snaps into the drill. The battery will not begin to charge until this snap has occurred.
Charging Inconsistency
While charging your batteries, keep the battery between 65-75 degrees, making sure to never keep it below 60 or above 80, to ensure that the batteries are accurately being charged. Charging outside of this temperature range will shorten battery life to some degree, ultimately shortening the amount of time the drill can hold its charge while in use.
Faulty Battery
Once the battery on the drill begins to die, take the battery out and place it to charge. By doing this, you avoid running the battery down to nothing which over time diminishes the life of the battery. Consistently taking care of the battery by charging it as soon as the battery life runs low will ensure that the battery holds its charge for the maximum amount of time possible while in use.
Drill Chuck
The drill chuck will not respond.
Dirt and Debris
Clean the chuck thoroughly to remove any excess debris that may hinder the drill’s movement. If the chuck is still unresponsive after thorough cleaning, you may need to replace your chuck.
Trigger Locked
The trigger is stuck and will not give under pressure.
Dirt and Debris
Clean around the trigger thoroughly to remove any dirt and debris that may be blocking the trigger. If the trigger is still jammed, there may be something internally preventing the trigger moving.
Trigger Position
Make sure the forward-reverse button is not in the center position. The center position serves as a safety and purposely locks out the drill. Push the forward-reverse button to the left if you want to drill forward, or push it to the right if you want to drill in reverse. Your direction will also be indicated by little arrows on either side of the forward-reverse button.
Drill Won’t Turn On
The drill will not respond when you press on the trigger.
Loose Battery
Try re-inserting the batteries. If this doesn’t help, your batteries may be dead and you may need to charge them.
Screw Won’t Catch Wood
The screw will not catch the wood properly and slips when drilling.
Forward/Reverse Control Button
Push the forward-reverse control button with your right finger, so it is sticking out of the left side of the drill. This will put the drill in forward mode so the drill is turning clockwise.
Drill Bits Falling Out of the Chuck
‘’Drill bits are not staying in the chuck. ‘’
Bits are not properly secured into the chuck
To ensure the bits are properly secured into the chuck, follow these steps:
1. Disconnect battery from the drill.
2. Grasp the black sleeve surrounding the chuck with one hand and secure the tool with the other hand. Rotate the chuck sleeve counterclockwise to open the chuck.
3. Insert the drill bit about ¾” into the opening on the chuck. Secure the bit by rotating the sleeve in the clockwise direction with one hand and holding the drill in the other.
4. To release the drill bit, repeat steps 1 and 2.
Команду
Cal Poly, Team 25-5, Maness Spring 2016 Участник Cal Poly, Team 25-5, Maness Spring 2016
CPSU-MANESS-S16S25G5
4 членов
Автор 4 руководств
24 Комментариев
My dewalt brushless 20 volt is stuck in a nonstop spining motion the trigger is not stuck and works fine but it wont stop until i take out the battery
Dan - Ответить
My dewalt 771 brand new can’t keep bits from falling out I have a cheap drill I never had a problem with I would of expected to get a better drill with a name brand like dewalt and I have a lot of dewalt cordless tools and I’m taking this drill back and if dewalt can’t make a better drill than this I’m going to switch over to Milwaukee
David Harrel - Ответить
I have a brand new dewalt 771 I bought it in a combo kit I have had a few months and never used it but when I do go to use it the bit keeps falling out this is the biggest pos drill I have ever owned I will never buy another dewalt tool if this is the kind of junk they are putting out I have a bunch of dewalt cordless tools but after this drill I think I’m going to start switching over to Milwaukee they have better warranty also but I used to be a dewalt fan until now
David Harrel - Ответить
Mine too. Total POS. Hammer doesn't work.
Chris Laughren -
The torque adjustment is stuck between 1 and 15 on a little image of a drill and doesn’t move. What do I do to release it or fix it? Thanks.
David Laffitte - Ответить
My battery charger will not charge my batteries
Calvin Hodges - Ответить
I've owned countless Dewalt cordless tools including many drills. I have rarely seen a product line go down hill so rapidly. Bits slip and won't stay chucked, Chuck has no way on which to get a good grip, and overall construction simply and absolutely socks! I purchased instead a Milwaukee combo set and it's as if I left the stone age and landed on a couch watching high definition and eating ribs fresh off the amazon prime system. I would encourage everyone to join me and get your fill of a truly incredible Milwaukee drill and driver kit.
D. Ward - Ответить
To keep the bit from falling out, make sure you have the drill in the right mode: right before the 1-15 torque settings there is a small drill bit symbol… select this and your bits will stay put. Worked for me.
Robert Smith - Ответить
This thing is utter garbage. Bringing it back, will never buy dewalt again
Geoff Salmon - Ответить
Had this drill for about two months, used it a few times then one time as I tried to use the power died. I thought it was the battery so I replaced the battery with a fully charged one but same thing happened. Each time I squeezed the trigger it’ll work until the trigger is released then the power light shuts off and it died. It won’t start or light up no matter how you wiggle or turn the drill until you take off the battery and reattached it. I opened up the housing and see nothing wrong as all the wires seemed to be attaching to its components as they should. What is the problem? Need help
Outdoor Slugger - Ответить
Hey, I am also having same problems ,have you ever found out what’s the problem?
New Worker -
I have a DCD771, perfect battery that I use elsewhere, when I pull the trigger no matter the spin setting, the LED flashes on once for less than a second, and nothing else happens. The chuck doesn’t spin, there’s no whirring noise, the motor doesn’t activate. Nothing.
Bryan - Ответить
I have EXACTLY the same problem - did you find solution?
David Colbourne -
I have the Dwalt dcd771, purchased April of 2019.
I have to battaries and the Drill seems like it have no power. i’m thinking the drill doe to the fack i have two power pack having the same issue
mikebrownsfan - Ответить
Once pressing the trigger it engages for about 2 to 4 seconds then it cuts off. What’s the problem?
Dennis C Smith - Ответить
just ordered a new dewalt kit of 7 tools for $400 and got the drill out to use for the first time and it worked when i pressed the trigger but when i let off the trigger it would not start working again until the light would go off and that has a 20sec delay . So every time I let off the trigger I have to wait 20 sec for the light to go off before I can press the trigger for it to work. NOT A HAPPY CAMPER!!!! After spending $400 dollars on what I thought was the premier brand name of cordless tools I find out that they’re junk too.
bwhte - Ответить
When I try to use as an Ice auger it starts to get very hot and overheats. Smoke comes out and then it doesn’t work for a while.
Steven Schambach - Ответить
I have a dewalt dcd771 type 2 when i start to drill the bit stops and the drill makes a grinding sound . How can i fix it or should i replace the drill .
anthony dangelo - Ответить
From what I just viewed on u-tube it sounds like the transmission is shot which is a common cause. Can be self-repaired if inclined to but not sure of cost.
Popeye8843 -
Bought the dcd791 Jan ‘19 as a kit with compact drill, bat., bag, charger from amazon & it’s Feb ‘22, 3yrs 1mon. makes 3yr warranty void! ‘HARDLY’ used it & out of nowhere gear stuck in 2nd & shifter in-op & won’t budge. Dewalt rep says ‘so sorry but not covered’ anymore & gives me a service center 700mi away! Uggghhh….so I’m SOL & stuck with a LEMON. Not sure if I’m staying with this product.
Popeye8843 - Ответить
I have purchased 3 new DeWalt DCD796N XR Li-Ion Brushless drills and each of them have the same problem ... the bits fall out. I even purchased a new chuck from the Dewalt repair center, but after trying every method of replacement offered by Dewalt and U-tubers, I ended up throwing the entire drill in the garbage. Dewalt has a serious quality control problem. Time for a change I guess.
Tom Gilmore - Ответить
Torque adjustment stuck on new drill
Doug Harmon - Ответить
My dewalt 771 will only work with the small 20-v lithium 2ah batteries and will not work with the xr 5ah batteries. This just happened the other day out of no where. Any help?
Jason DeRose - Ответить
My new 20volt drill when in reverse will go reverse on first pull of trigger and if let off a pull trigger again it goes forward????
Art Slade - Ответить