Home Button hard to click

Question

iPhone 5s

Компания Apple представила iPhone 5s 10 сентября 2013 года. Ремонт данного устройства схож с предыдущими моделями, требующий отвертки и инструменты для вскрытия. Доступен в версиях GSM или CDMA; с 16, 32 или 64 ГБ памяти; в цветах: Серебристый, Золотой и «Серый космос».

3530вопросов Показать все

Amarjit Singh @amarjitsin57883

Репутация: 13

1

Опубликовано: 7 мар 2016 г.

Опции

Home Button hard to click

I have a iPhone 5s, that I recently replaced the screen on. After doing this the home button was not clickable, it has to be now pressed either at an angle or really deep for the click to happen. I replaced the screen and button just as I took it off but it is not clicking as easily as before. The Touch ID work fine the button it self works as intended and click, just needs to be correctly clicked.

I reopened the phone and tried to tighten the shield screws but that is as much as they would go.if i where to hold the backside of the home button (while screen opened) and click it, it works and gives tactile feedback of being clicked.

I am here looking for suggestions on how to get it to be clicky again, so i can feel the tackticle response and it works.

Отвечено! Посмотреть ответ У меня та же проблема

Это хороший вопрос?

Да Нет

Оценка 1

Добавить комментарий

5 Ответов

Выбранное решение

iMedic @theimedic

Репутация: 57,5к

iMedic Phone Repairs

18

77

212

Опубликовано: 14 апр 2017 г.

Опции

Ok, so first let's make sure the plate is facing the right way, that's a good way to make this not work properly

iPhone 5s Home Button Replacement

After that, it is totally possible the part you've gotten wasn't molded properly, and the home button won't sit where it's supposed to. A lot of my 6/6+/6S/6S+ parts come with a sticker around that hole, and mess things up. I basically just have to remove the sticker. If you've tried all these things and it still won't sit right. Get your part exchanged. If they won't do it, PayPal usually sides with the buyer, and you could get your money back

Был ли этот ответ полезен?

Да Нет

Оценка 3

Добавить комментарий

Nigel @romeobravodelta Репутация: 209 4 1 · Answer 1 · 2016-03-07T23:20:39-07:00

Nigel @romeobravodelta

Репутация: 209

4

1

Опубликовано: 7 мар 2016 г.

Опции

Try to loosen the screws up a bit. Over tightening screws could result in the rigidness that you are experiencing.

Был ли этот ответ полезен?

Да Нет

Оценка 1

3 Комментариев:

Just tried that and did not work out.

7 мар 2016 г. из Amarjit Singh

Is everything aligned correctly?

Try rotating the button in place (with screen removed) and see if it's not aligning correctly?

8 мар 2016 г. из Nigel

Yeah I tired that also, my issues is not related to position or screws. It is a issue related to the clickability of it. The click is not happening and must be pressed down deep for it to register.

8 мар 2016 г. из Amarjit Singh

Добавить комментарий

clemensstift @clemensstift Репутация: 49 2 1 · Answer 2 · 2016-06-11T01:59:59-07:00

clemensstift @clemensstift

Репутация: 49

2

1

Опубликовано: 11 июн 2016 г.

Опции

Had the same issue. I just reopened it, took the button out, put it back in and this time, didn't tighten the screws so hard. Clicks just fine now!

Был ли этот ответ полезен?

Да Нет

Оценка 0

Добавить комментарий

Kevin Gonzalez @kevingonza47115 Репутация: 1 · Answer 3 · 2017-04-14T17:18:00-07:00

Kevin Gonzalez @kevingonza47115

Репутация: 1

Опубликовано: 14 апр 2017 г.

Опции

gat rubbbing alcohol and dip ur finger then rub ur finger around the button and let some alcohol go in and loosen it up

Был ли этот ответ полезен?

Да Нет

Оценка 0

1 Комментарий:

I would be very careful of this, as you could easily get the IP into the display, and immediately it would very damaged, but over time it would only appear slightly damaged

14 апр 2017 г. из iMedic

Добавить комментарий