Эта версия возможно содержит некорректные исправления. Переключить на последнюю проверенную версию.
Выберете то, что вам нужно
-
Этот шаг не переведен. Помогите перевести
-
Power off your iPhone before beginning disassembly.
-
Remove the two 3.9 mm Pentalobe screws from either side of Lightning connector.
-
-
Этот шаг не переведен. Помогите перевести
-
If your display glass is cracked, keep further breakage contained and prevent bodily harm during your repair by taping the glass.
-
Lay overlapping strips of clear packing tape over the iPhone's display until the whole face is covered.
-
-
Этот шаг не переведен. Помогите перевести
-
Regardless of the tool you use, you need to be sure you pull up the entire display.
-
If the glass begins to separate from the plastic, as shown in the first image, slide a plastic opening tool between the plastic frame and the metal phone body to pry the metal clips out of the case.
-
-
Этот шаг не переведен. Помогите перевести
Инструмент, используемый на этом этапе:Anti-Clamp$24.95-
Pull the blue handle backwards to unlock the Anti-Clamp's arms.
-
Slide the arms over either the left or right edge of your iPhone.
-
Position the suction cups near the bottom edge of the iPhone just above the home button—one on the front, and one on the back.
-
Squeeze the cups together to apply suction to the desired area.
-
-
Этот шаг не переведен. Помогите перевести
-
Pull the blue handle forwards to lock the arms.
-
Turn the handle clockwise 360 degrees or until the cups start to stretch.
-
Insert an opening pick under the screen when the Anti-Clamp creates a large enough gap.
-
Skip the next two steps.
-
-
Этот шаг не переведен. Помогите перевести
-
If you don't have an Anti-Clamp, use a single suction cup to lift the front panel:
-
Press a suction cup onto the screen, just above the home button.
-
-
Этот шаг не переведен. Помогите перевести
-
While holding the iPhone down with one hand, pull up on the suction cup to slightly separate the home button end of the front panel from the rear case.
-
With a plastic opening tool, gently pry the edges of the rear case down, away from the front panel assembly, while you pull up with the suction cup.
-
-
Этот шаг не переведен. Помогите перевести
-
Pull the plastic nub to release the vacuum seal on the suction cup.
-
Remove the suction cup from the screen.
-
-
Этот шаг не переведен. Помогите перевести
-
Open the phone just enough to reveal the metal bracket covering the home button cable.
-
Only the phone's original home button assembly will be capable of using the Touch ID functionality. If you rip the cable, installing a new home button will only restore ordinary home button functions, not the Touch ID features.
-
Use the tip of a spudger to push the bracket free and remove it with tweezers.
-
-
Этот шаг не переведен. Помогите перевести
-
Use the tip of a spudger to pry the home button cable connector up out of its socket.
-
-
-
Этот шаг не переведен. Помогите перевести
-
Once the connector has been released, pull the home button end of the assembly away from the rear case, using the top of the phone as a hinge.
-
Open the display to about a 90º angle, and lean it against something to keep it propped up while you're working on the phone.
-
Add a rubber band to keep the display securely in place while you work. This prevents undue strain on the display cables.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the two 1.6 mm Phillips #000 screws securing the metal battery connector bracket to the logic board.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the metal battery connector bracket from the iPhone.
-
-
Этот шаг не переведен. Помогите перевести
-
Use the flat end of a spudger to gently pry the battery connector up from its socket on the logic board.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the following screws securing the front panel assembly cable bracket to the logic board:
-
One 1.7 mm Phillips #000 screw
-
One 1.2 mm Phillips #000 screw
-
One 1.3 mm Phillips #000 screw
-
One more 1.7 mm Phillips #000 screw
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the front panel assembly cable bracket from the logic board.
-
-
Этот шаг не переведен. Помогите перевести
-
Use a spudger or a fingernail to disconnect the front-facing camera and sensor cable.
-
-
Этот шаг не переведен. Помогите перевести
-
Insert a SIM card eject tool or a paperclip into the small hole in the SIM card tray.
-
Press to eject the tray. This may require a significant amount of force.
-
-
Этот шаг не переведен. Помогите перевести
-
Use a spudger to gently pry the button assembly cable up from its socket on the logic board.
-
-
Этот шаг не переведен. Помогите перевести
-
Use a spudger to pry the Lightning connector cable up from its socket on the logic board.
-
Fold the Lightning connector cable out of the way of the logic board.
-
-
Этот шаг не переведен. Помогите перевести
-
Use the tip of a spudger to pry the antenna cable up from its socket on the logic board.
-
-
Этот шаг не переведен. Помогите перевести
-
Use the flat end of a spudger to disconnect the rear-facing camera cable from its socket on the logic board.
-
-
Этот шаг не переведен. Помогите перевести
Инструмент, используемый на этом этапе:Standoff Screwdriver for iPhones$5.49-
Remove the following screws from the logic board:
-
One 2.4 mm Phillips #000 screw
-
Two 2.3 mm Phillips #000 screws
-
Four 2.8 mm standoff screws
-
-
Этот шаг не переведен. Помогите перевести
-
Use a plastic opening tool to lift the logic board up enough to grab with your fingers.
-
-
Этот шаг не переведен. Помогите перевести
-
Pull the logic board slightly away from the rear facing camera.
-
Flip the logic board toward the battery, as if you are turning the page in a book.
-
-
Этот шаг не переведен. Помогите перевести
-
Use the flat end of a spudger to disconnect the antenna cable on the back of the logic board.
-
Remove the logic board from the iPhone.
-
-
Этот шаг не переведен. Помогите перевести
-
At this point, a small metal plate near the rear facing camera is loose and may come free from its recess.
-
Use tweezers to remove the plate from beneath the bracket to the left of the rear-facing camera.
-
Отменить: Я не выполнил это руководство.
92 участников успешно повторили данное руководство.
18 Комментариев
where can I buy a logic board?
There is not much of a used market for these yet so they will be hard to come by. Most will be from dead units. You can try ebay for broken phones just be careful what you buy.
Eddie -
If the phone is dead, is ir viable to buy the logic board, or ir wont work? How can I know wich to buy? Is there an important issue or information to know obout logic boards. I will really apreciatte if someone tell me all the necessary things to know. Thanks
Were can I buy a new motherboard for iPhone se
Can i get iphone se motherboard plz