Этот профиль еще не завершен.
Вопросы
I swapped my iPhone 7 Plus into a new housing and the cameras don’t work now front and and back. For some reason in 3u...
Читать далееI did a housing swap on an iPhone 7 and LTE would be acting weird. Like right now I did a dfu restore and it’s saying no...
Читать далееI’m planing to upgrade my CPU in my mid 2007 iMac since it’s socketed. So would a Core 2 Duo T9400 work with my Mac?
Читать далее== Ok so I have a a1278 MacBook Pro and the fan Is spinning at full speed. But it’s showing 0 rpm in macs fan control. And...
Читать далееHi, I’m converting a late 2007 MacBook a.k.a Santa Rosa architecture MacBook with a 2009 motherboard. I was wondering if...
Читать далееHi I have a iphone5s that I replaced the battery and charging connecter on but when I put the new battery in it was stuck...
Читать далееОтветы
I’ve dealt with this issue a few times with eBay phones, Some ways I dealt with rounded bottom screws was to superglue the bit to the screw and let it sit there for like a day and that trick worked. More destructive ways are to well get a small drill bit and drill the head of the screw off. Or the final way after everything fails is to separate the screen from the plastic rails that run along the side of it, keep in mind this will most likely destroy the screen but you’ll have access to the internals but it will leave the hole plugged up with a screw.
Читать далееWouldn’t recommend using a water damaged battery, The actual cell of the battery could be questionable or the controller board on the battery could be bad. Not worth risking frying a logic board.
Читать далееAs Reece said there’s no technical real fix to a iCloud locked board as Apple will always see the S/N as locked. However if you really need it to work you can use a tool called Checkra1n then pay to get service working as well as being untethered. The service is called sonick14, keep in mind if you restore the phone with a computer it will become ic locked again.
Читать далееError 4013 is cause by a misbehaving NAND or just flat out faulty NAND. First I would try other tools before you declare this phone bricked. Like try to use 3u tools or something like that. Typically if a device can’t leave DFU mode then the logic board needs to be repaired.
Читать далееThe pixels in the actual LCD coulv’ve been damaged from the shock of being dropped. So a new LCD would fix this.
Читать далееHave you tried changing the wifi antenna in the MacBook? Also is there any corrosion or bent pins in the airport card slot. Maybe try to use a wifi card from a 2010 iMac. Because it works with my a1260 MacBook Pro and it’s not by Broadcom. But you may need to update Mac OS since it’s a newer wifi card Hope this Helps,
Читать далееAn 860 evo or any hard drive or ssd should work fine since it’s a standard sata interface. Also the 2011 MacBook pros have sata 3 so everything should be compatible. And to clone a Mac hard drive I would get sata to USB. Also if you want to cloan the Hard drive on to the ssd use an app called Super Duper it makes it easy to transfer all of your data Hope this Helps, Ronan
Читать далееDisconnecting the battery when the Phone is on is fine and The digitizer on the display probably died because it was so damaged
Читать далееThere’s also a tool Called Mac Post Factor it can put 10.8 up to 10.12 on a 3,1 MacBook. Keep in mind that you will need the OS X update file for this. https://osxhackers.net/macpostfactor/
Читать далееOk first step I would try is restoring via iTunes it could be software. If it isn’t it’s going to be hardware. So either the home button went bad or the cable that connects Touch ID to the motherboard is bad. And finally one of the connectors may have popped out, but that’s uncommon . Hope this helps
Читать далееСтраница 1 из 2
Ronan
@ronan0s
247
Репутация
16
Ответов
0
Руководства
Пользователь с 06/13/18