Перейти к основному содержанию

Flip Video LCD Screen

Выберете то, что вам нужно

  1. Flip Video LCD Screen, Outer Shell: шаг 1, изображение 1 из 2 Flip Video LCD Screen, Outer Shell: шаг 1, изображение 2 из 2
    • Turn off the device and take the batteries out.

    • Remove metal sticker under the LCD screen with a spudger.

    • This may require a large force to pry off the glued sticker.

  2. Flip Video LCD Screen: шаг 2, изображение 1 из 1
    • Remove the 4 gray screw caps with the spudger. These cover the screw heads and protect from dirt or grime.

  3. Flip Video LCD Screen: шаг 3, изображение 1 из 2 Flip Video LCD Screen: шаг 3, изображение 2 из 2
    • Remove the 5 10mm screws with the #00 Phillips screwdriver. These connect the back of the outer shell to the front of the outer shell.

  4. Flip Video LCD Screen: шаг 4, изображение 1 из 1
    • Open battery door. This can be done by gently depressing and sliding the battery down downward.

  5. Flip Video LCD Screen: шаг 5, изображение 1 из 1
    • Use the spudger to separate outer shells.

    • The spudger must be inserted between the shell halves to pry the edges apart.

    • Slowly work around the outside to separate the halves.

  6. Flip Video LCD Screen, Circuit Board: шаг 6, изображение 1 из 1
    • Remove the 3 5mm screws securing the circuit board to the front shell with the #00 Phillips screwdriver.

  7. Flip Video LCD Screen: шаг 7, изображение 1 из 1
    • Slowly lift the left side of the circuit board.

    • Do not attempt to remove the circuit board completely yet. It is still connected to the device.

  8. Flip Video LCD Screen: шаг 8, изображение 1 из 1
    • Disconnect the USB port cable from the back side of the circuit board.

  9. Flip Video LCD Screen: шаг 9, изображение 1 из 1
    • Slide out the battery contacts.

    • Battery contacts

    • Slot where battery contacts were located

  10. Flip Video LCD Screen, LCD Screen: шаг 10, изображение 1 из 1
    • With the LCD screen facing away from you, remove the 2 bronze 3 mm screws securing the LCD using the #00 Phillips screwdriver.

  11. Flip Video LCD Screen: шаг 11, изображение 1 из 1
    • Flip over the circuit board and unlock the two black tabs on the ribbon connector by sliding them upwards.

  12. Flip Video LCD Screen: шаг 12, изображение 1 из 1
    • Gently pull out ribbon cable.

    • If the ribbon cable does not come out easily you may not have fully unlocked the ribbon cable connector in the previous step.

    • The LCD screen is now removed and can be replaced.

Заключение

To reassemble your device, follow these instructions in reverse order.

Еще один человек закончил это руководство.

Elizabeth

Участник с: 04/15/10

100 Репутация

Автор 6 руководств

Команда

Cal Poly, Team 26-21, Regan Spring 2010 Участник Cal Poly, Team 26-21, Regan Spring 2010

CPSU-REGAN-S10S26G21

4 членов

Автор 12 руководств

0 Комментариев

Добавить комментарий

Просмотр статистики:

За последние 24часов: 0

За последние 7 дней: 1

За последние 30 дней: 7

За всё время: 5,227