Введение

Use this guide to replace the battery in your Huawei Mate 8 smartphone.

Switch off your phone and remove the SIM card tray.
  • Switch off your phone and remove the SIM card tray.

Добавить комментарий

Remove the Torx T2 screws from the bottom of the phone
  • Remove the Torx T2 screws from the bottom of the phone

Добавить комментарий

  • Use an iSclack or a suction handle in the bottom area of your phone to separate the display unit from the rear panel.

Добавить комментарий

  • Use an opening pick to fully separate the clips, releasing the phone.

    • Do not fully remove the rear case. The fingerprint sensor cable is still connected to the back cover.

  • Open the phone like a book from the SIM tray side.

  • Use a spudger, to disconnect the fingerprint sensor cable.

Добавить комментарий

  • Remove the liquid indicator sticker.

  • Remove the Phillips #00 screw that holds down the metal shield.

  • The metal shield is tightly held in place. If you try to remove it without holding it down on one side, it'll break easily.

  • Use a spudger to remove the metal shield.

Добавить комментарий

  • Use the flat end of a spudger to disconnect the display, daughterboard interconnect, and battery cables.

Добавить комментарий

  • Remove the Phillips #00 screw that holds down the interconnect cable bracket.

Добавить комментарий

  • Lift the coaxial connector off of its socket to allow access to the daughterboard interconnect cable bracket.

  • Remove the bracket.

Добавить комментарий

  • Use a spudger to disconnect the interconnect cable.

  • Remove the interconnect cable.

Добавить комментарий

  • The battery is glued in place with two adhesive strips. One with a pull tab and one without.

  • Get a good grip on the pull tab near the power button and peel out the adhesive strip by steadily pulling at the tab in a flat angle.

    • If the adhesive strip rips, grab and twist it around the tweezer tips a couple of times and then continue.

Добавить комментарий

  • Do not bend or puncture the battery, damage to the cell can cause battery fires.

  • Heat an iOpener and place it on the phone for about a minute to loosen the remaining adhesive.

  • Carefully insert the flat end of a spudger to separate any remaining adhesive at the top of the battery.

Добавить комментарий

  • Lift the top end of the battery to pull the battery off of the remaining adhesive strip.

    • When reassembling your phone apply new adhesive where it is necessary.

  • Never reinstall a battery that has been bent or damaged during removal.

Добавить комментарий

Заключение

To reassemble your device, follow these instructions in reverse order. When reassembling your phone apply new adhesive where it is necessary.

8 участников успешно повторили данное руководство.

Dominik Schnabelrauch

Участник с: 23.11.2016

17 069 Репутация

Автор 90 руководств

Команда

iFixit Member of iFixit

Community

106 членов

Автор 6 491 руководств

Комментариев: 3

great guide changed my battery in under 30 min thank you @schnabel

george austin - Ответить

Hi George,

nice to hear and i hope your phone works well!

Dominik Schnabelrauch -

Thank you for an excellent guide! Clear instructions and great pictures. I followed the steps and it worked flawless. One comment regarding Step 4 - I had greater luck opening from bottom side up rather than from left to right.

Jim My - Ответить

Добавить комментарий

Просмотр статистики:

За 24 часа: 11

За 7 дней: 131

За 30 дней: 615

За всё время: 3,898