Перейти к основному содержанию

Введение

You will learn how to remove and install the resistance spring.

Запчасти

No parts specified.

  1. Hold the mouse so that the bottom is facing up.
    • Hold the mouse so that the bottom is facing up.

    • Locate the #1 screw towards the bottom half of the mouse.

    • Take the 4.76 mm Phillips screwdriver and unscrew the #1 screw.

  2. Place the mouse so that the bottom is resting against a hard surface . Gently lift the top cover of the mouse and remove.
    • Place the mouse so that the bottom is resting against a hard surface .

    • Gently lift the top cover of the mouse and remove.

  3. Locate the scroll wheel on the mouse. Grab the scroll wheel with your thumb and index finger. Gently lift up to remove the scroll wheel from the mouse.
    • Locate the scroll wheel on the mouse.

    • Grab the scroll wheel with your thumb and index finger.

    • Gently lift up to remove the scroll wheel from the mouse.

  4. Locate the spring on the scroll wheel. The spring is a small piece of metal wire coiled in the middle. Carefully remove the spring from the wheel scroll.
    • Locate the spring on the scroll wheel. The spring is a small piece of metal wire coiled in the middle.

    • Carefully remove the spring from the wheel scroll.

  5. Replace the spring, place it on the correct side of the wheel with the prongs pointing down. The correct side is the side without the black plastic square, as shown in the photos.
    • Replace the spring, place it on the correct side of the wheel with the prongs pointing down.

    • The correct side is the side without the black plastic square, as shown in the photos.

  6. Be aware of where the resistance spring is. This spring will easily fall off. Grab the scroll wheel and its mount and gently pull them apart.
    • Be aware of where the resistance spring is.

    • This spring will easily fall off.

    • Grab the scroll wheel and its mount and gently pull them apart.

  7. Grasp the top of the resistance spring. Pull it towards yourself so the bottom slides out of its hole. Grasp the top of the resistance spring. Pull it towards yourself so the bottom slides out of its hole.
    • Grasp the top of the resistance spring. Pull it towards yourself so the bottom slides out of its hole.

  8. To install the resistance spring, place the hooked section of the spring into the corresponding hole on the mount.
    • To install the resistance spring, place the hooked section of the spring into the corresponding hole on the mount.

Заключение

To reassemble your device, follow these instructions in reverse order.

8 участников успешно повторили данное руководство.

Maximilian Betkowski

Участник с: 11.01.2013

175 Репутация

Автор 4 руководств

Команда

Cal Poly, Team 5-14, Forte Winter 2013 Member of Cal Poly, Team 5-14, Forte Winter 2013

CPSU-FORTE-W13S5G14

5 членов

Автор 7 руководств

Комментариев: 4

This mouse was also available from Dell as an OEM device under the model name "M-UVDEL1". Hopefully the Google juice will help folks repair their devices. I know I would have spent far more time than I did if it weren't for the photos on how to put the spring back. Thanks Maximilian!

Bastien Nocera - Ответить

The spring installation details were lifesavers. Thank you!

LB

byard - Ответить

thank you! could not have done it without your help.

taiyo_yuden_dvd - Ответить

Brilliant. Thanks. Easy once you know how. The springs were the hard part.

Charles Thomson - Ответить

Добавить комментарий

Просмотр статистики:

За 24 часа: 3

За 7 дней: 16

За 30 дней: 49

За всё время: 5,171